This Class T Fuse and Fuse block are designed for use with 3/8 ring terminal connections. The fuse block features a black polycarbonate, fiberglass reinforced base with a clear polycarbonate touch safe snap-on cover.All Stainless Steel HardwareReplaceable FuseFuse Block Max. Height is 2.5"..

This Class T Fuse and Fuse block are designed for use with 3/8 ring terminal connections. The fuse block features a black polycarbonate, fiberglass reinforced base with a clear polycarbonate touch safe snap-on cover.All Stainless Steel HardwareReplaceable FuseFuse Block Max. Height is 2.5"..

The SI25-PEL64R-4 from IMO Precision Controls is a rotary actuator switch lockable off in plastic enclosure. This True DC isolator is specifically developed as a True DC switch to disconnect the DC/AC inverter from the photovoltaic panels. All photovoltaic installations have to be equipped with DC isolators in accordance with IEC 60364-7-712. The IMO SI is a True DC switch not an AC version de-rat..

Individual fuseIncludes single pole fuse bar, fuse insulating cap and hardware..

BMV-712 SmartWith Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. With Bluetooth being implemented in most other Victron Energy products, wireless communication between products will simplify system installation and enhance performance...

Lynx Power InA modular DC bus bar, used to connect batteries to the Lynx DC distribution system...

SmartShuntThe Smart Battery ShuntThe SmartShunt is an all in one battery monitor, only without a display. Your phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on your phone (or tablet) and you can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.Alternatively the SmartShunt can ..

Wall mount enclosure for BMV and Color Control GXEasily mount a BMV and MPPT Control on a wall...

Wall mount enclosure for Color Control GXWall mount enclosure for Color Control GX..

Extend Battery Life + 1 Year or MoreSpecialized for keep up the voltage balance of batteries connected in series during the Charging and Discharging process, due to differences in the chemical composition and temperature of the battery cell that connected in series, It causes two battery charge and discharge differences even the battery is idle, also due to the different levels of self-discharge c..

Battery Fuse Disconnector 250AApplication ScopeThunderVolt fuse switch disconnector is applicable to high short circuit current circuit with AC 50(60)Hz, voltage up to 660V and rated working currentup t0 630A. Fuse Switch disconnector possesses upper and lower end input and output structure. Lead in equipment with knife-edge and arcextinguishing equipment, and also can be operated with load. It is..

Battery Life SaverBattery Desulfator for 48V Electric Vehicles or Battery BanksBLS-48ABLS-48A is designed for use in 48 volt renewable energy battery banks or use with battery powered vehicles (Use the (BLS 48N) for 48 volt golf carts). Ideally mounted full time to constantly keep the batteries in optimum condition, the BLS-48A comes with 3/8″ eye rings for attachment to the battery terminals..

Protect your electrical components and wiring with high amperage ANL fuses. Secure your ANL fuses with VTE ANL Fuse Holders, a low-cost and practical platform for over-current protection.Highly cost effective solutions for 50 - 300 amp fusingMultiple Fuse Amperage AvailableFuse Holder ANB740 Max Amperage: 300 amps @ 12 vdcFor fuses over 300 amp, VTE recommends the Hi-Amp ANL Fuse HolderFuses Rated..

Feature·        Clamp allows measurement of AC current in wires without disturbing the circuits or contacting live terminals·        Auto range simplifies operation: 0.01-400 Amps, 0.001-600 Volts·        Auto power-off selection - power turns off automatically after 10 minutes of non-use·..

Protect your electrical components and wiring with high amperage ANL fuses. Secure your ANL fuses with VTE ANL Fuse Holders, a low-cost and practical platform for over-current protection.Highly cost effective solutions for 50 - 300 amp fusingMultiple Fuse Amperage AvailableFuse Holder ANB740 Max Amperage: 300 amps @ 12 vdcFor fuses over 300 amp, VTE recommends the Hi-Amp ANL Fuse HolderFuses Rated..